Equipment
Showing 1–20 of 310 results
-
“I” Bar or Straight Bar Sealers
I Bar Sealers – Table top Impulse I bar sealer with starter roll of PVC shrink film and heat gun included.
-
# 304 Stainless Steel Conveyors
Available in 3ft-20 ft lengths- Product handling conveyors. These all stainless steel construction conveyors feature plastic slat top or stainless steel top conveyors..
-
1 ONLY 3M model 200A adjustable top and bottom carton sealer, 110 volt
-
1 ONLY Eastey Model ET3620 High Capacity Shrink tunnel, Tunnel size of 36″ W x 20″ H x 52″ L. 220 volt, 3 phase power.
-
1 ONLY Little David LD7 Top and Bottom case taper, 110 volt 2″ tape head.
-
1 ONLY Preferred Pack Model PP2028MKA-V-PI with air operated seal head adjustable inverting triangle and powered film unwind. 220 volt, 1 phase.
-
1 ONLY Preferred Pack Model PP3040MKA-V-PI with air operated seal head adjustable inverting triangle and powered film unwind. 220 volt, 1 phase.
-
180 Degree Turn Conveyors
180 Degree Curved Conveyors and straight sections all 15 1/2″ wide. Straight sections available in lengths of 24, 36 or 72″ long. Also 90 degree conveyors available.
-
3 ft Flighted Infeed
Lugged infeed conveyors available in 3 ft and 6 ft lengths. 18″ Lugged spacing. Variable speed conveyor drive.
-
36″ and 48″ Accumulating Turntables Stainless Steel
36″ and 48″ Diameter turntables available in Stainless Steel construction
-
36″, 48″ and 60″ Lazy Susan Turntable
Lazy Susan Product Accumulators 36”, 48″and 60″ Diameter turntables. The variable speed turntable 0 to 12 RPM allow you to accumulate a large volume of product in one area. Great for accumulating smaller products that will not transfer on a roller or skatewheel conveyor. Plugs into any 110 volt outlet. All units available in stainless steel.
-
4 ea Shanklin Model T-8 Large capacity shrink tunnel with opening of 28″ W x 18″ H x 47″ L Excellent condition, well maintained. 480 Volt 3 Phase, 30 amp
-
405 T
18″ x 24″ seal area. Operator loads product onto board and place in seal area, operator manually pulls out frame to initiate seal cycle.
-
411 T
An auto cycle machine with full manual over ride controls. The 411 features many of the standard features of the 420T with a less automated packaging cycle. The 411T features an 18″ x 24″ seal size with automatic heat and vacuum initiation. The vacuum range is fully adjustable and the production monitor keeps track of packaging cycles. The 411T meets the demands of a fulltime packaging line that requires less automation.
-
420 T
A full automatic cycle machine with full manual override controls. User friendly operation allows for high production or simple one-of-a-kind or test packaging. The high efficiency oven provides the fastest cycle with a minimum of energy. User friendly analog controls eliminate any need to access computers or programs.
-
5 Belco Tunnels available, Model ST2214 High Speed Shrink Tunnels 480 volt, 3 phase, 30 amp Tunnel opening is 22″ W x 14″ H x 48″ L
-
6 ft Belted Infeed
3 ft and 6 FT. Belt conveyors, 15″ wide, Variable speed drive.
-
6 ft Flighted Infeed
Lugged infeed conveyors available in 3 ft and 6 ft lengths. 18″ Lugged spacing. Variable speed conveyor drive.
-
6 ft Paddle Conveyors
6 FT. Long Flighted In-Feed Conveyor for wide products, uses wide pusher
-
610 R
The 610 R2 has been engineered and designed for efficient, trouble free production. Our introductory model has all the the features needed for production die cutting at a very modest cost. 18″ x 24″ cutting area. An infinitely adjustable pressure roller allows quick setup and precise control to help extend the life of your tooling. (Die setup and changeover is a matter of minutes.) Accurate indexing is provided by registration clips which hold materials in proper relation to the cutting die. The single pass cutting and rapid cycling features, coupled with quick changeover and trouble free operation will dramatically increase your production rate and package quality.